250mm Hydrocyclone Sand Washing 30t/H Hydrocyclone In Mineral Processing

Place of Origin: Chengdu, China
Certification: ISO 9001, ISO 14001, ISO 45001
Model Number: HC-PU-250
Minimum Order Quantity: 1 Set
Packaging Details: Export-grade wooden case with stretch film and shock-proof foam, apex and vortex finder packed separately
Delivery Time: 7-15 days for stock, 20-30 days for production
Payment Terms: T/T,L/C,PayPal,Western Union
Supply Ability: 300 Sets per Month
Inquiry Now
Get A Quote
Specifications
Highlight Features

250mm Hydrocyclone Sand Washing

,

Hydrocyclone Sand Washing 30t/H

,

30t/H Hydrocyclone In Mineral Processing

Cone Diameter:
250 Mm (10 Inch)
Feed Head:
Replaceable PU, Tangential Inlet
Nominal Feed Capacity:
25 - 35 T/h At 0.1 MPa
Apex Spigot Range:
25 / 32 / 40 Mm Replaceable
Vortex Finder Range:
65 / 75 / 85 Mm Replaceable
Body Weight:
38 Kg Assembled
Installation:
Bolt-on Flange Or Quick Clamp, Frame Or Skid Mounted
Wearing Parts:
Apex Spigot, Vortex Finder, One-piece Liner, Gaskets
Product Description

250mm Hydrocyclone With One-Piece PU Liner for Sand Washing

250mm Hydrocyclone PU One Piece Liner Sand Washing Desliming 30 t/h Feed Capacity

Sand washing plants lose money twice when a cyclone liner fails: once on the spare itself, and again on the downtime while a crew cuts out a worn section and patches it. This 250 mm unit removes the second loss by casting the whole inner chamber as a single polyurethane body, so there is no joint, no seam and no patch line for fine sand to attack.

One-Piece Liner, No Joints to Fail

The inlet head, cylindrical section, cone and apex seat are moulded from one continuous cast, then bonded into a steel shell. Slurry never meets a bonded overlap, which is where conventional sectional liners start to peel. Because the liner carries the wear, the outer shell stays clean and can be reused across two or three liner life cycles.

  • Single casting: no liner seams, no field gluing, no premature edge wear.
  • Even wall thickness: the casting keeps the designed profile all the way to the apex, so the separation curve stays where it was set.
  • Field replaceable: the liner is lifted out of the split shell with the unit still on its frame.

Stable Classification on Variable Sand Feed

Apex and vortex finder are both replaceable PU parts with matching seat geometry. Operators can shift the cut point to follow changes in feed solids without swapping the whole cyclone, and the PU surface keeps the internal diameter true far longer than steel, so the grading curve drifts little between shutdowns.

Light Enough to Fit Without a Crane

The PU liner and thin-wall shell bring the bare unit into a two-person lift on most skid frames. Flange or quick clamp connection means a unit can be changed out during a normal maintenance window rather than a planned plant stop. Polyurethane also shrugs off the constant water contact of a washing circuit, so hydrolysis is not a service factor.

Complete Unit and Spares From One Source

Shipments can combine assembled cyclones with a matching spares kit: apex spigots, vortex finders, liners, feed chambers and gaskets. Every unit is built under ISO 9001, ISO 14001 and ISO 45001 certified production.

Technical Parameters

Liner Type One-piece hot cast polyurethane (PU) liner
Liner Hardness 88 - 92 Shore A
Housing Material Carbon steel with anti-corrosion coating, SS304 optional
Feed Pressure 0.06 - 0.25 MPa
Separation Range 10 - 150 µm
Classification Efficiency ≥ 85%
Underflow Spigot Replaceable PU spigot, ceramic option
Overflow Vortex Finder Replaceable PU vortex finder
Hydrolysis Resistance ≥ 85% tensile retention after 168 h immersion at 70 ℃
Corrosion Resistance pH 2 - 13 slurry with chloride bearing water
Process Connection Bolt-on flange / quick clamp, DN50 - DN200
Spare Parts Kit Apex spigot, vortex finder, inner liner, feed chamber, gaskets

Typical Duty

Silica and natural sand washing, desliming ahead of a dewatering screen, and fines recovery where a steady 10 - 150 µm cut matters more than raw throughput.

Send your feed curve, solids content and target cut size, and we will confirm the apex and vortex finder combination for your circuit.

Related Products
Send an Inquiry