125mm Hydrocyclone Cluster Lightweight PU Liner Fine Particle Classification 8 Way

Place of Origin: Chengdu, China
Certification: ISO 9001, ISO 14001, ISO 45001
Model Number: HC-PU-125C8
Minimum Order Quantity: 1 Set
Packaging Details: Cyclones nested in export-grade wooden case, manifold and clamps in separate carton, foam separators between bodies
Delivery Time: 10-18 days for stock, 25-35 days for production
Payment Terms: T/T,L/C,PayPal,Western Union
Supply Ability: 400 Sets per Month
Inquiry Now
Get A Quote
Specifications
Highlight Features

125mm Hydrocyclone Cluster

,

Lightweight Hydrocyclone Cluster

,

8 Way Hydrocyclone

Cone Diameter:
125 Mm (5 Inch) Per Unit
Cluster Size:
8 Units On One Manifold, 2 To 16 Units On Request
Nominal Feed Capacity:
8 - 12 M3/h Per Unit At 0.15 MPa
Apex Spigot Range:
12 / 16 / 20 Mm Replaceable
Vortex Finder Range:
35 / 40 / 45 Mm Replaceable
Body Weight:
11 Kg Per Unit Assembled
Installation:
Quick Clamp Or Bolt-on Flange On Manifold, No Lifting Gear Required
Wearing Parts:
Apex Spigot, Vortex Finder, One-piece Liner, Gaskets
Product Description

125mm Hydrocyclone Cluster for Fine Particle Classification

125mm Hydrocyclone Cluster Lightweight PU Liner Fine Particle Classification 8 Way

Fine classification is usually a space problem before it is a separation problem. Small diameter cyclones give the sharp cut that fine duty needs, but a single 125 mm unit cannot carry the flow, and a bank of them can become a maintenance liability. This cluster is arranged so the whole bank stays serviceable.

Built Around Light Weight

Each 125 mm cyclone uses a thin-wall shell with a one-piece cast polyurethane liner, which brings the individual unit weight down to a level one fitter can handle on a manifold. That changes installation entirely: the frame only has to carry the process load, not a bank of heavy steel cones.

Installation Sequence

  • Position the manifold or distribution head and anchor to the frame.
  • Offer each cyclone up to its feed port; quick clamp or bolt-on flange engages without alignment jigs.
  • Fit the apex spigot of the required bore for the target cut.
  • Tighten, pressure test and start; a single unit can be swapped later without disturbing its neighbours.

Fine Cut Held by One-Piece Lining

A 125 mm body has little tolerance for wear. Because the liner is cast as one piece, the cone taper, the apex seat and the inlet geometry all stay to drawing, which is what keeps the classification curve steady on fine feeds. There is no joint at the apex end, the area that wears first and fastest.

Service Water and Reagents Are Not a Problem

Polyurethane resists hydrolysis and works across pH 2 - 13, so the same liner suits clay slurries, wash water and reagent-bearing process water without a material change. Individual units and spares are interchangeable across the bank, so one spares kit covers the whole installation.

Technical Parameters

Liner Type One-piece hot cast polyurethane (PU) liner
Liner Hardness 88 - 92 Shore A
Housing Material Carbon steel with anti-corrosion coating, SS304 optional
Feed Pressure 0.06 - 0.25 MPa
Separation Range 10 - 150 µm
Classification Efficiency ≥ 85%
Underflow Spigot Replaceable PU spigot, ceramic option
Overflow Vortex Finder Replaceable PU vortex finder
Hydrolysis Resistance ≥ 85% tensile retention after 168 h immersion at 70 ℃
Corrosion Resistance pH 2 - 13 slurry with chloride bearing water
Process Connection Bolt-on flange / quick clamp, DN50 - DN200
Spare Parts Kit Apex spigot, vortex finder, inner liner, feed chamber, gaskets

Typical Duty

Kaolin and clay classification, fine silica and frac sand cut points, pigment and filler slurries, and any duty where 10 - 75 µm separation has to be achieved in a compact footprint.

Tell us your flow rate and target cut size and we will propose the number of units, apex bore and manifold arrangement.

Related Products
Send an Inquiry