75mm Desliming Hydrocyclone Hydrolysis Resistant PU Liner Clay

Place of Origin: Chengdu, China
Certification: ISO 9001, ISO 14001, ISO 45001
Model Number: HC-PU-075K
Minimum Order Quantity: 1 Set
Packaging Details: Export-grade wooden case, cyclone and spare kit packed in separate foam-lined compartments
Delivery Time: 7-15 days for stock, 20-30 days for production
Payment Terms: T/T,L/C,PayPal,Western Union
Supply Ability: 500 Sets per Month
Inquiry Now
Get A Quote
Specifications
Highlight Features

75mm Desliming Hydrocyclone

,

Desliming Hydrocyclone Hydrolysis Resistant

,

PU Liner Clay Hydrocyclones

Cone Diameter:
75 Mm (3 Inch)
Feed Head:
Replaceable PU, Tangential Inlet
Nominal Feed Capacity:
3 - 6 M3/h At 0.2 MPa
Apex Spigot Range:
8 / 10 / 12 Mm Replaceable
Vortex Finder Range:
22 / 25 / 28 Mm Replaceable
Body Weight:
5 Kg Assembled
Spare Kit Contents:
2 Apex Spigots, 1 Vortex Finder, 1 Liner, 1 Feed Chamber, Gasket Set
Wearing Parts:
Apex Spigot, Vortex Finder, One-piece Liner, Feed Chamber, Gaskets
Product Description

75mm Hydrocyclone for Clay and Chemical Slurry Desliming

Small cyclones in clay, kaolin and chemical plants spend their life in water that is warm, slightly acidic or alkaline, and often loaded with dissolved salts. In that environment the liner material decides the maintenance interval, not the flow rate. This 75 mm unit is specified for exactly that service.

Hydrolysis Resistance Measured, Not Assumed

The cast polyurethane used here retains over 85 percent of its tensile strength after 168 hours of immersion at 70 ℃, which means the liner does not soften, swell or go chalky in a continuously wet circuit. A one-piece casting removes the bonded seams where water ingress normally starts.

Corrosion Across the Working pH Range

The liner operates in slurries from pH 2 to pH 13, including chloride bearing process water, without a protective coating that could chip. Where a steel body would need a coating maintenance programme, the polyurethane surface simply keeps working.

Fine Cut Point Held at Small Diameter

A 75 mm cone produces a sharp cut between 10 and 40 µm, and because the liner is cast in one piece the apex seat and cone taper stay concentric. That keeps the classification curve repeatable even after several apex changes.

Spare Parts Kit Supplied With the Unit

  • Two apex spigots in the bore sizes you run
  • One vortex finder, matched to the feed duty
  • One spare one-piece liner
  • Feed chamber and a set of gaskets

Every part is a drop-in fit, so a changeover does not need measuring, cutting or bonding. Complete units and kits are produced under ISO 9001, ISO 14001 and ISO 45001 certified systems.

Technical Parameters

Liner Type One-piece hot cast polyurethane (PU) liner
Liner Hardness 88 - 92 Shore A
Housing Material Carbon steel with anti-corrosion coating, SS304 optional
Feed Pressure 0.06 - 0.25 MPa
Separation Range 10 - 150 µm
Classification Efficiency ≥ 85%
Underflow Spigot Replaceable PU spigot, ceramic option
Overflow Vortex Finder Replaceable PU vortex finder
Hydrolysis Resistance ≥ 85% tensile retention after 168 h immersion at 70 ℃
Corrosion Resistance pH 2 - 13 slurry with chloride bearing water
Process Connection Bolt-on flange / quick clamp, DN50 - DN200
Spare Parts Kit Apex spigot, vortex finder, inner liner, feed chamber, gaskets

Typical Duty

Kaolin and ball clay desliming, ceramic and glaze slurry classification, chemical precipitate washing and pigment fines recovery.

Describe your slurry chemistry and target cut and we will confirm the liner grade, apex bore and kit contents.

Related Products
Send an Inquiry