Quick Link
Quick Contact
Address
No.367 Beijing Road, Longquanyi District, Chengdu, China
Tel
86--13981727059
Our Newsletter
Subscribe to our newsletter for discounts and more.
Custom Cut Polyurethane Dewatering Screen Panel Matched to Your Own Deck Drawing
Most dewatering decks in service were not built to a round metric number. Frames get re-railed, side plates get welded on, and the original panel drawing stops matching the machine. Ordering a catalogue panel of the nearest size means new holes in the frame, gaps at the edges and a deck that drains unevenly. The panel in this listing is made the other way round: the drawing comes first and the mould follows it.
Drawing before mould. Send a dimensioned sketch, a photo of the deck with key measurements, or a scanned outline of a worn panel with the fixing holes marked. We return a setting-out drawing for your signature, then cut the mould from that drawing. Nothing goes into production until the drawing is agreed in writing.
Pin centres and rail spacing matched. Panel outline, pin hole diameter, hole position, corner radii and any cut-outs for side liners are taken from your drawing. A panel that lands on the existing pins needs no frame work, no re-drilling and no adapter rails.
Mixed sets on one pallet. A single deck often needs two or three different panels: a coarser first section, a fine discharge section, a left hand and a right hand version. We number each panel on the drawing and pack the set together so the fitter works from the set plan rather than from loose parts.
Mould lead time stated up front. New mould making is typically 10 days and panel production 15 days after drawing approval. That figure is quoted before the order is placed, not discovered afterwards, so a planned shutdown can be scheduled around it.
Where it runs
Retrofit dewatering decks, imported vibrating screens with non-standard frames, replacement of mixed-brand decks, and any installation where the original panel is no longer available from the machine builder.
Technical data
|
Item |
Specification |
|
Thickness |
40 mm standard; 25–60 mm on request |
|
Panel size |
1044 mm x 702 mm standard; custom cut to your deck drawing |
|
Aperture |
0.1–100 mm slotted or square; tapered option |
|
Hardness |
Shore A 85 (75–95 available) |
|
Compound |
Hydrolysis-resistant wear grade polyurethane |
|
Density |
1.10–1.15 g/cm³ |
|
Tensile strength |
≥ 30 MPa |
|
Tear strength |
≥ 80 kN/m |
|
Abrasion (DIN 53516) |
≤ 40 mm³ |
|
Rebound resilience |
≥ 40 % |
|
Service temperature |
−30 °C to +80 °C |
|
Fixing |
Pin and sleeve, bolt-through, or rail clamp |
Customisation
Quote against a drawing, not against a catalogue size. Panel outline, slot width, fixing hole centres, corner radii and any cut-out for a side liner are all taken from the setting-out drawing you approve, so the panel is a direct fit for the deck already on site. Left and right hand versions, or two different slot widths on one deck, are numbered on the drawing and packed as one set.
Ordering
Send the deck drawing or a measured sketch, the slot width you are running, the number of panels per deck and the screen motion. If a worn panel is still available, mark the fixing holes and send a photo of it on a flat floor with a rule alongside.
FAQ
Can you copy a panel I send you?
Yes. A worn panel with the holes marked and photographed flat with a rule is usually enough to set out the drawing. We confirm the dimensions back to you before cutting.
What if my drawing is only approximate?
We will flag every dimension that cannot be confirmed from the information supplied and ask for a photo or a second measurement before the mould is cut.
Do you make panels for machines you did not supply?
Yes. Almost all of this work is for existing decks from other builders, including imported screens where the original panel is no longer supplied.