Custom Made Dewatering Panel 42% Open Area PU Screen Hydrolysis Resistant

Place of Origin: Chengdu, China
Certification: ISO 9001, ISO 14001, ISO 45001
Model Number: PU-DW-1044x702
Minimum Order Quantity: 10 Pieces
Packaging Details: Export-grade wooden pallet with stretch film and shock-proof foam
Delivery Time: 7-15 days for stock, 20-30 days for production
Payment Terms: L/C,T/T
Supply Ability: 5000 Pieces per Month
Inquiry Now
Get A Quote
Specifications
Highlight Features

custom made dewatering panel

,

pu screen hydrolysis resistant

,

42% open area pu screen

Panel Size:
1044mm X 702mm (custom Sizes Available)
Thickness:
40mm Standard (25-60mm On Request)
Aperture:
0.1-100mm Slotted Or Square, Tapered Option
Hardness:
Shore A 85 (75-95 Available)
Connection:
Pin And Sleeve, Bolt-through, Or Rail Clamp
Material:
Hydrolysis-resistant Wear Grade Polyurethane
Application:
Mine Tailings, Coal, Sand And Gravel Dewatering
Product Description

Custom Made Polyurethane Dewatering Screen Panel with Ridge Surface and 42 Percent Open Area

Open area is the first number anyone looks at on a dewatering panel, and it is also the easiest one to misread. A flat panel with 42 percent open area and a bed sitting on top of it does not drain like a 42 percent deck, because the water under the bed has nowhere to break out. Raising the surface into ridges changes the geometry of the bed itself, and that is where the extra drainage comes from.

Ridges lift the bed off the flat. The raised lines run along the deck and carry the load of the bed while the slots sit in the valleys between them. Water reaches the apertures through a shorter path and the bed is thinner over the openings, so the same open area drains measurably faster.

Open area used where it counts. Perforations are distributed across the whole panel face rather than concentrated in a central band. Combined with the ridge profile, that gives up to 42 percent open area over the working surface instead of a nominal figure that only applies to the middle of the panel.

Coarse section first, fine section last. The usual arrangement on a dewatering deck is a coarser slot at the feed end to take the bulk water away immediately, and a fine slot at the discharge end to work on the film. Panels are supplied as a numbered set so the layout is built into the order.

Ridges stiffen the panel as well as drain it. The ridge profile adds section stiffness, so a 40mm panel holds its plane across a wide deck with fewer support rails and does not sag into the gaps between them. A deck that stays flat drains evenly across its width.

Where it runs

Coal tailings and slurry dewatering, mineral processing de-mediuming, sand and gravel wash water recovery, and any high tonnage deck where the limiting factor is drainage rate rather than slot size.

Technical data

Item

Specification

Thickness

40 mm standard; 25–60 mm on request

Panel size

1044 mm x 702 mm standard; custom cut to your deck drawing

Aperture

0.1–100 mm slotted or square; tapered option

Hardness

Shore A 85 (75–95 available)

Compound

Hydrolysis-resistant wear grade polyurethane

Density

1.10–1.15 g/cm³

Tensile strength

≥ 30 MPa

Tear strength

≥ 80 kN/m

Abrasion (DIN 53516)

≤ 40 mm³

Rebound resilience

≥ 40 %

Service temperature

−30 °C to +80 °C

Fixing

Pin and sleeve, bolt-through, or rail clamp

Customisation

The ridge profile, the ridge pitch and the orientation along or across the deck are all set in the mould, so the drainage pattern follows the way the bed actually travels on your deck. Slot width is made to the product band, and the panel outline and fixing positions follow your deck drawing.

Ordering

Send the tonnage, the feed solids content, the target moisture at the discharge and the deck layout from feed to discharge. A photo of the current deck showing where it blinds is more useful than a slot dimension on its own.

FAQ

Does the ridge profile wear faster than a flat panel?

No. The ridge carries the bed, so the wear is distributed along the raised lines and the slots between them are protected from direct abrasion.

Can the ridge run across the deck instead of along it?

Yes. The orientation is set in the mould and is chosen from the deck slope and the way the bed travels.

Is 42 percent open area available on every slot width?

Open area falls as the slot narrows. 42 percent applies to the coarser slots; fine slot panels trade open area for retention.

Related Products
Send an Inquiry