Quick Link
Quick Contact
Address
No.367 Beijing Road, Longquanyi District, Chengdu, China
Tel
86--13981727059
Our Newsletter
Subscribe to our newsletter for discounts and more.
OEM Custom Size Polyurethane Dewatering Screen Panel with Fine Slots Down to 0.1mm
Below about 1mm, a dewatering deck stops behaving like a screen and starts behaving like a filter. Water no longer falls through an open hole; it has to be persuaded to leave a bed that is sitting directly on the apertures, and any particle that lodges in a slot stays there. Fine slot polyurethane panels work on that basis, and the slot geometry matters far more than the open area figure on the datasheet.
Slot width held to a tolerance, not to a nominal figure. Fine slots are moulded and then checked against the ordered width. A slot quoted at 0.25mm that arrives at 0.35mm passes product it should retain, and the loss shows up in the underflow rather than in a complaint.
Tapered slot, not a straight one. The slot is wider on the underside than at the surface. A particle that enters the top of the slot has clearance to pass through instead of wedging halfway, which is the difference between a deck that blinds over a shift and one that stays open.
Water leaves a polyurethane surface more readily. Polyurethane has a lower affinity for water than rubber, so the film on the panel breaks away instead of clinging. On fine duties where the bed is thin, that property does more for the final moisture figure than a small change in slot width.
Fine slot does not have to mean short life. The wear-resistant compound is the same one used on coarse panels, so the deck keeps its slot width instead of polishing open over the campaign. If a screen is being replaced every few months because the slots have worn wide, the compound is usually the cause rather than the duty.
Where it runs
Tailings dewatering and de-sliming, coal slurry recovery, mineral concentrate filtration, wet sand classifying where fines loss is the constraint, and any deck running below 1.5mm.
Technical data
|
Item |
Specification |
|
Thickness |
40 mm standard; 25–60 mm on request |
|
Panel size |
1044 mm x 702 mm standard; custom cut to your deck drawing |
|
Aperture |
0.1–100 mm slotted or square; tapered option |
|
Hardness |
Shore A 85 (75–95 available) |
|
Compound |
Hydrolysis-resistant wear grade polyurethane |
|
Density |
1.10–1.15 g/cm³ |
|
Tensile strength |
≥ 30 MPa |
|
Tear strength |
≥ 80 kN/m |
|
Abrasion (DIN 53516) |
≤ 40 mm³ |
|
Rebound resilience |
≥ 40 % |
|
Service temperature |
−30 °C to +80 °C |
|
Fixing |
Pin and sleeve, bolt-through, or rail clamp |
Customisation
Slot width, panel outline and fixing positions are all made to order, so a non-standard frame is not a problem. If the deck was built for a different panel and the holes no longer line up with a catalogue size, the drawing is cut to the deck as it is now rather than the deck being modified to suit the panel.
Ordering
Send the product band you need to retain, the slot width you are currently running, the feed solids content and the deck dimensions. If fines are being lost to the underflow, send the underflow gradation so the slot can be set against what is actually passing.
FAQ
What is the finest slot you can mould?
0.1mm is the practical floor. Below that the slot is difficult to hold in production and blinds very quickly in service.
Will a finer slot always give a drier product?
No. A finer slot drains more slowly and blinds more readily. On most fine duties the drier product comes from the right slot plus a thinner bed, not from the smallest slot in the catalogue.
Can I get two slot widths on one deck?
Yes. A coarser first section and a fine discharge section are supplied as one numbered set, which is the usual arrangement on tailings decks.